This is the latest recevied telemetry packets stored in our database for station/object OK2PYA-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | TX* | RX* | Digi* | V_Bat* | V_Ext* |
|---|---|---|---|---|---|
| 1758170401 | 625 Count | 609 Count | 590 Count | 4.29 VDC | 0 VDC |
| 1758168475 | 587 Count | 573 Count | 554 Count | 4.29 VDC | 0 VDC |
| 1758166548 | 550 Count | 537 Count | 519 Count | 4.29 VDC | 0 VDC |
| 1758164622 | 505 Count | 494 Count | 476 Count | 4.29 VDC | 0 VDC |
| 1758162695 | 472 Count | 463 Count | 445 Count | 4.29 VDC | 0 VDC |
| 1758160768 | 427 Count | 419 Count | 402 Count | 4.28 VDC | 0 VDC |
| 1758160359 | 403 Count | 400 Count | 383 Count | 4.29 VDC | 0 VDC |
| 1758154579 | 292 Count | 292 Count | 278 Count | 4.29 VDC | 0 VDC |
| 1758152653 | 263 Count | 263 Count | 251 Count | 4.29 VDC | 0 VDC |
| 1758150724 | 223 Count | 225 Count | 213 Count | 4.29 VDC | 0 VDC |
| 1758148797 | 186 Count | 190 Count | 178 Count | 4.29 VDC | 0 VDC |
| 1758144944 | 107 Count | 110 Count | 103 Count | 4.29 VDC | 0 VDC |
| 1758143018 | 63 Count | 68 Count | 61 Count | 4.29 VDC | 0 VDC |
| 1758139165 | 981 Count | 946 Count | 923 Count | 4.28 VDC | 0 VDC |
*Used Equation Coefficients:
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)