This is the latest recevied telemetry packets stored in our database for station/object CR7BQX-15. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | TX* | RX* | Digi* | V_Bat* | V_Ext* |
|---|---|---|---|---|---|
| 1758141973 | 611 Count | 389 Count | 389 Count | 4.33 VDC | 0.14 VDC |
| 1758141070 | 609 Count | 388 Count | 388 Count | 4.35 VDC | 0.14 VDC |
| 1758140167 | 606 Count | 386 Count | 386 Count | 4.3 VDC | 0.14 VDC |
| 1758139264 | 604 Count | 385 Count | 385 Count | 4.28 VDC | 0.14 VDC |
| 1758138361 | 601 Count | 383 Count | 383 Count | 4.28 VDC | 0.14 VDC |
| 1758137457 | 599 Count | 382 Count | 382 Count | 4.26 VDC | 0.14 VDC |
| 1758136554 | 596 Count | 380 Count | 380 Count | 4.27 VDC | 0.14 VDC |
| 1758135651 | 594 Count | 379 Count | 379 Count | 4.34 VDC | 0.14 VDC |
| 1758134748 | 591 Count | 377 Count | 377 Count | 4.28 VDC | 0.14 VDC |
| 1758133845 | 589 Count | 376 Count | 376 Count | 4.33 VDC | 0.14 VDC |
| 1758132942 | 587 Count | 375 Count | 375 Count | 4.29 VDC | 0.14 VDC |
| 1758132039 | 585 Count | 374 Count | 374 Count | 4.3 VDC | 0.14 VDC |
| 1758131136 | 580 Count | 370 Count | 370 Count | 4.3 VDC | 0.14 VDC |
*Used Equation Coefficients:
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)